Our Products
   
By Product Type, Brand or Keyword
Services

Featured Products & Specials
Parts, Accessories, Rental, Repair
Our Quality testing process!
Request a Quote / More Information
Customer Survey
Operations Manuals - Download

Request an RMA

Ardus Medical
Baxter Pump, Baxter Colleague 3CS Infusion Pump

Baxter Colleague 3CS Triple Channel Infusion Pump

Baxter Colleague 3CS Infusion Pump

Baxter Colleague 3CS Infusion Pump

Save up to 80% on pre-owned Baxter Colleague 3CS infusion pumps.
   Request A QUOTE!


Product Specifications

Ac power Requirements:
100-120 VAC, 60Hz

Leakage Current:
Less than 300 u amps earth leakage (tested per UL 2601)

External Fuses:
1.6 amp Type T (time delay) 250V

Power Cord:
2.9 m (9 feet) long with integrally molded hospital grade plug

Battery Supply System:
Colleague 3 Pump - 3 hours operating time at 100 mL/hr for all three channels (fully charged new batteries) 12 hours to recharge to 80% of capacity Internal charge system recharges batteries whenever the device is connected to an AC outlet

Range of Programmable Flow Rates:
Primary Infusion on each pump channel 0.1 to 99.9 mL/hr in 0.1 mL/hr increments 1 to 1200 mL/hr in 1 mL/hr increments Piggyback Infusion on each pump channel 0.1. to 99.9 mL/hr in 0.1 mL/hr increments 1 to 500 mL/hr in 1 mL/hr increments Note: Rate limits can be configured for values less Than those stated above.

Volume to be Infused:
0.1 - 99.9 mL in 0.1 mL increments 1- 9999 mL mL/hr in 1 mL increments
Note: Volume to be Infused limits can be configured for values less than those stated above

KVO:
0.1 - 5 mL/hr in 0.1 mL increments (configurable option) or programmed rate whichever is less.

Priming rate:
500 mL/hr (to be used only when not connected to patient)

Advance Air Rate to Advanced an Air Bubbles:
At the same rate programmed for the current primary or piggyback infusion.

Air Bubble Setting:
Measured accumulations of approximately
25 microliters
50 microliters
100 microliters 150 microliters
The Air Bubble Setting is a configurable option.

Auto Restart:
Allows the pump channel to automatically restart if an occlusion is relieved within one minute after detection. This configuration option allows 0 to 9 restarts before manual intervention is required.

Nominal Downstream:
Alarm sensitivity is a configurable option. Rate range in mL/hr

<21
2 psig (Minimum)
5 psig (Moderate)
9 psig (Maximum)

21- 200
5 psig (Minimum)
8 psig (Moderate)
12 psig (Maximum)

>200
6 psig (Minimum)
11 psig (Moderate)
15 psig (Maximum)

Device Size:
Approximately 13.88" H x 7.75" W x 8.00" D
(353 x 197 x 203 mm)
Not including clamp knob or power cord

Device weight:
Approximately 17.5 lbs (7.9 kg)

Environmental Operating Limits:
59º F - 100º F (15º C - 38º C)

Environmental Storage and Transport Limits:
-20º F - 135º F (-29ºC - 57º C), 10-100% Reliable Humidity including condensation, 500-1060 hPa Barometric Pressure

Ground Impedance:
Less than 0.2 ohms (tested per UL-2601)

Solution Container Height:
Pump will operate at all programmable flow rates with a solution container height ranging from -36 to +48 inches. Container height is measured from the pump channel selected for use.

Interfaces:
Attachment to a remote nurse call system A variety of systems exist which enable alert and alarm conditions to be transmitted to a remote location via the communications port on the rear panel assembly of the pump. See the service manual for additional information.

For service, parts, PM or rental see our Services section


      Slothworks
Copyright © 2010 All Rights Reserved. Ardus Medical, Inc. | 1-855-59-Ardus | info@ardusmedical.com | Site Map